[lustre-discuss] Replacing ldiskfs MDT with larger disk
jesse.stroik at ssec.wisc.edu
Wed Jul 31 14:10:15 PDT 2019
This is excellent information, Andreas.
Presently we do file level backups to the live file system and they take
over 24 hours, so they're done continuously. For that timeframe to wrok,
we'd need to be able to back up and recover the MDT to the new MDT with
the file system online.
Given that resizing the file system will proportionately increase the
inodes (I didn't realize that), dd to a logical volume may be a
reasonable option for us. The dd would be faster enough that we could
weather the downtime.
PFL and FLR aren't features they're planning for the file system and it
may be replaced next year so I suspect they'll opt for the DNE method.
On 7/31/19 3:11 PM, Andreas Dilger wrote:
> Normally the easy answer would be that a "dd" copy of the MDT device from your HDDs to a larger SSD LUN, then resize2fs to increase the filesystem size would also increase the number of inodes proportionately to the LUN size.
> However, since you are *not* using 1024-byte inode size, only 512-byte inode size + 512-bytes space for other things (ie. 1024 bytes-per-inode ratio), I'd suggest a file-level MDT backup/restore to a newly-formatted MDT because newer features like PFL and FLR need more space in the inode itself. The benefit of this approach is that you keep a full backup of the MDT on the HDDs in case of problems. Note that after backup/restore the LFSCK OI Scrub will run for some time (maybe an hour or two, depending on size), which will result in slowdown. That would likely be compensated by faster SSD storage.
> If you go the DNE route, then migrate some of the namespace to the new MDT, you definitely still need to keep MDT0000. However, you could combine these approaches and still copy MDT0000 to new flash storage instead of keeping the HDDs around forever. I'd again recommend a file-level MDT backup/restore to a newly-formatted MDT to get the newer format options.
> Cheers, Andreas
>> On Jul 31, 2019, at 13:50, Jesse Stroik <jesse.stroik at ssec.wisc.edu> wrote:
>> Hi everyone,
>> One of our lustre file systems outgrew its MDT and the original scope of its operation. This one is still running ldiskfs on the MDT. Here's our setup and restrictions:
>> - centos 6 / lustre 2.8
>> - ldiskfs MDT
>> - minimal downtime allowed, but the FS can be read-only for a while.
>> The MDT itself, set up with -i 1024, needs both more space and available inodes. Its purpose changed in scope and we'd now like the performance benefits of getting off of spinning media as well.
>> We need a new files system instead of expanding the existing ldiskfs because we need more inodes.
>> I think my options are (1) a file level backup and recovery or direct copy onto the new file system or (2) add a new MDT to the system and assign all directories under the root to it, then lfs_migrate everything on the file system thereafter.
>> Is there a disadvantage to the DNE approach other than the fact that we have to keep the original spinning-disk MDT around to service the root of the FS?
>> If we had to do option 1, we'd want to remount the current MDT read only and continue using it while we were preparing new MDT. When I searched, I couldn't find anything that seemed definitive about ensuring no changes to an ldiskfs MDT during operation and I don't want to assume i can simply remount it read only.
>> Jesse Stroik
>> lustre-discuss mailing list
>> lustre-discuss at lists.lustre.org
> lustre-discuss mailing list
> lustre-discuss at lists.lustre.org
-------------- next part --------------
A non-text attachment was scrubbed...
Size: 3964 bytes
Desc: S/MIME Cryptographic Signature
More information about the lustre-discuss